Missing Screw on Engine Casing?
Mar 4, 2011 | 3:07 pm
#1
Original Poster
Join Date: Jan 2007
Location: RTM
Programs: DiamondClub (rip), Currently an Alliance Treble Champion (BA, A3, AZ)
Posts: 1,804
Missing Screw on Engine Casing?
I just returned from a short turbo-prop (j41) segment where I happened to notice that one of the screws on the engine casing was missing. Is this something that I should have been worried about?
I raised with with the FA when I departed but it got me thinking - is this something that I should have (or in the future, should) raise with the crew before departure. (I didn't notice this time).
I raised with with the FA when I departed but it got me thinking - is this something that I should have (or in the future, should) raise with the crew before departure. (I didn't notice this time).
Mar 4, 2011 | 3:14 pm
#2
FlyerTalk Evangelist
Join Date: Mar 2008
Location: DFW
Posts: 30,950
I just returned from a short turbo-prop (j41) segment where I happened to notice that one of the screws on the engine casing was missing. Is this something that I should have been worried about?
I raised with with the FA when I departed but it got me thinking - is this something that I should have (or in the future, should) raise with the crew before departure. (I didn't notice this time).
I raised with with the FA when I departed but it got me thinking - is this something that I should have (or in the future, should) raise with the crew before departure. (I didn't notice this time).
A leading edge of a panel would be subject to more air forces than say a rear or side edge. But even then if enough fasteners remain to secure the panel then little is likely to happen.
I have many years experience in aviation maintenance. The real evidence is what did happen with the panel and missing screw?
Mar 4, 2011 | 3:23 pm
#3
Original Poster
Join Date: Jan 2007
Location: RTM
Programs: DiamondClub (rip), Currently an Alliance Treble Champion (BA, A3, AZ)
Posts: 1,804
No ill effects...! And it was in the middle of the panel not at the leading edge.. Just struck me as a bit odd and not exactly what you wanted to see when gawping out of the window at 22,000 ft a couple hundred miles from land 
Mar 4, 2011 | 3:23 pm
#4
Join Date: Feb 2011
Posts: 642
Are you just talking about the screws that hold the panels to the engine, e.g. such as the part seen opened here? If so, aircraft engines that have panels attached by screws instead of latches typically have many screws holding them on, and there are regulations as to how many can be missing. Depending upon the panel, a single one missing probably would not be an issue. There was probably an entry in the maintenance chart noting it and to have it replaced when next due.
BTW, missing screws, open and exposed sensitive areas, coincidence?!
BTW, missing screws, open and exposed sensitive areas, coincidence?!
Last edited by jtodd; Mar 4, 2011 at 3:31 pm
Mar 4, 2011 | 3:33 pm
#5
FlyerTalk Evangelist
Join Date: Mar 2008
Location: DFW
Posts: 30,950
Mar 4, 2011 | 8:33 pm
#8
FlyerTalk Evangelist
Join Date: Mar 2008
Location: DFW
Posts: 30,950
Mar 4, 2011 | 11:30 pm
#9
FlyerTalk Evangelist
Join Date: Dec 2004
Location: MSP
Programs: Fallen Plats, ex-WN CP, DYKWIW; still PAL Premier Elite & Hilton Diamond
Posts: 25,429
Mar 5, 2011 | 7:59 am
#11
Join Date: Feb 2011
Posts: 642
You would be surprised as to how often high speed tape is used on commercial aircraft in service. The most frequent that I have seen is when a new windows s put in the cockpit, it is used to cover the sealant around the window to allow it to dry properly.